DigiDesign MachineControl Specifications Page 87
- Page / 98
- Table of contents
- TROUBLESHOOTING
- BOOKMARKS
- SYNC I/O Guide 1
- Chapter 1. Introduction 3
- Chapter 4. Using SYNC I/O 3
- Introduction 5
- SYNC I/O Features 6
- System Requirements 7
- Digidesign Registration 8
- About the Pro Tools Guides 8
- About www.digidesign.com 9
- SYNC I/O Guide6 10
- Installation and Configuration 11
- Clock for Pro Tools 12
- Audio Interfaces 12
- Connecting Slave Clock for 13
- Pro Tools 13
- MachineControl 14
- Time Code Connections to 15
- Machines, Decks, and Other 15
- Synchronization and 15
- Connecting LTC 16
- Connecting Word Clock Devices 16
- Connecting AES/EBU Devices 16
- Software Installation 17
- Configuring Pro Tools 18
- SYNC I/O 18
- Configuring SYNC I/O in the 19
- Locked and Speed Cal LEDs 20
- Positional Reference 20
- Sample Rate 21
- Time Code Rate 21
- Feet+Frame Rate 21
- MachineControl Configuration 22
- Software Configuration for 22
- SYNC I/O Setup Software 22
- Configuring Pro Tools 23
- Updating SYNC I/O Firmware 23
- Firmware Messages 24
- Troubleshooting 25
- SYNC I/O Guide22 26
- SYNC I/O Front Panel 27
- Sample Rate LEDs 28
- Generator/Parameter Controls 28
- Time Code Display 28
- Positional Reference Switch 29
- Frame Rate Switch 29
- Status LEDs 29
- SYNC I/O Back Panel 30
- Video In/Out 31
- LTC In/Out 31
- AES/EBU In/Out 31
- SYNC I/O Guide30 34
- Bi-Phase/Tach Parameters 35
- Generator/Bi-Phase Preset 35
- Variable Speed Override (VSO) 35
- SYNC I/O Guide32 36
- Using SYNC I/O 37
- Available from/in: 38
- Pro Tools Front Panel 38
- SYNC I/O Setup 38
- Software Utility 38
- Front Panel 39
- Generator/Parameter 39
- Switches 39
- Clock References and Options 40
- Digital Clock 41
- LTC and Clock Reference 42
- Pilot Tone 43
- Regenerating 44
- Freewheel Duration 47
- VITC and Positional Reference 47
- Reference 48
- Serial Time Code 49
- SYNC I/O Guide46 50
- Read/Regeneration Mode 51
- Generator Preset Mode 52
- LTC Generation/Regeneration 53
- VITC Generation/Regeneration 54
- Internal VITC Generation 55
- SYNC I/O Guide52 56
- Generating a Window Burn 57
- SYNC I/O Guide54 58
- Chapter 4: Using SYNC I/O 55 59
- SYNC I/O Guide56 60
- Controls 61
- SYNC I/O Guide58 62
- VITC Generate Lines 63
- Window Dub/Burn 63
- Freewheel Length/Duration 63
- LTC Output Level/Gain 64
- Servo Gain 64
- Pitch Memory/Hold 64
- Bi-Phase/Tach Input Signal 65
- Video Format/System 65
- MTC Idle Mute 65
- Using Fader Start 66
- Calibrating the SYNC I/O 67
- Oscillator 67
- Restoring Factory Settings 68
- Managing and Selecting Video 69
- SYNC I/O Guide66 70
- Video and VITC Signals 71
- Auto-Switch LTC/VITC 72
- LTC Signals 72
- Digital Clock Signal Types 73
- Bi-Phase/Tach 74
- SYNC I/O Guide72 76
- Technical Specifications 77
- Rear Panel Connectors 80
- Bi-Phase/GPI/Pilot 86
- GPI Relay Outputs 88
- GPI (TTL)/MTC Outputs 89
- GPI (opto) Inputs 90
- Connector Pin Assignments 91
- SYNC I/O Serial Cable Pin 93
- Assignments 93
- Bi-phase/Tach/GPI/Pilot Port 93
- Interfacing Notes 93
- GPI Triggers 94
- GPI TTL WIring 94
Related products and manuals for Software DigiDesign MachineControl
(126 pages)
(73 pages)
© 2020, manymanuals.com. All rights reserved. | 0.028 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals