DigiDesign D-Control Specifications Page 109
- Page / 164
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Chapter 9: Management and Soft Key Sections 101
Actions Switch (Page 2)
Wrt To Start (Write To Start) Writes current automation val-
ues from the insertion point backward to the beginning of a
selection or track while performing an automation pass.
Wrt To Punch (Write To Punch Point) Writes current automa-
tion values back to the point where writing of automation be-
gan
Wrt To All (Write to All) Writes current automation values to
an entire selection or track while performing an automation
pass.
Wrt To End (Write to End) Writes current automation values
from the insertion point forward to the end of a selection or
track while performing an automation pass.
Wrt To Next (Write to Next Breakpoint) Writes current auto-
mation values from the insertion point forward to the next
automation breakpoint while performing an automation pass.
Snap Back Causes all Latch or Write enabled tracks to exit
their current automation pass and return instantly to the pre-
viously written automation levels. During playback, this com-
mand stops writing of automation without applying any Au-
toMatch ramping.
Actions Switch (Page 3)
Wrt To Currnt (Write To Current Parameter) Writes the current
control value to the currently displayed automation parame-
ter (Edit > Automation > Write To Current).
Wrt To All Ena (Write To All Enabled Parameters) Writes cur-
rent control values to all enabled automation parameters (Edit
> Automation > Write To All Enabled).
Trm To Currnt (Trim To Current Parameter) Applies the current
trim value to the currently displayed automation parameter
(Edit > Automation > Trim To Current).
Trm To AllEna (Trim To All Enabled Parameters) Applies cur-
rent trim values to all enabled automation parameters (Edit >
Automation > Trim To All Enabled).
Gld To Currnt (Glide To Current Parameter) Applies a transition
between automation values to the currently displayed auto-
mation parameter (Edit > Automation > Glide To Current).
Gld To AllEna (Glide To All Enabled Parameters) Applies a tran-
sition between automation values to all enabled automation
parameters (Edit > Automation > Glide To All Enabled).
Actions Switch (Page 4)
Copy To Send Opens the Copy To Send dialog to allow copy-
ing of track control values to each selected track’s send (Edit >
Automation > Copy To Send).
Thin Auto (Thin Automation) Performs the Thin Automation
command. (Edit > Automation > Thin).
Colesc VCAAtm (Coalesce VCA Automation) Executes the
Track > Coalesce VCA Master Automation command
Colesc TrmAtm (Coalesce Trim Automation) Executes the
Track > Coalesce Trim Automation Command
Clear TrmAtm (Clear Trim Automation) Executes the Track >
Clear Trim Automation Command
Suspend TrmAtm (Suspend Trim Automation) Temporarily sus-
pends Trim automation to allow auditioning of Trim moves
- D-Control 1
- Contents 5
- D-Control Guidevi 6
- Contents vii 7
- D-Control Guideviii 8
- Part I: Introduction 9
- D-Control Features 11
- D-Control System Components 11
- System Expansion Options 12
- Operational Requirements 12
- Connection Requirements 12
- System Requirements 12
- Mechanical Specifications 13
- D-Control Guide6 14
- Chapter 2: D-Control Overview 15
- D-Control Guide8 16
- Main Unit Back Panel 17
- D-Control Fader Module 18
- D-Control XMON Interface 19
- XMON Back Panel 20
- Part II: Installation 21
- D-Control Stand 23
- Stand Components 24
- Stand Hardware 25
- Placement of D-Control 26
- Preparing the Stand Legs 26
- Assembling the Stand 27
- Installing D-Control Units 30
- Moving the Spacer Plate 31
- D-Control Guide24 32
- Closing Up the Stand 33
- Installing a Video Display 35
- D-Control Guide28 36
- D-Control Guide30 38
- (Optional) 39
- D-Control Guide32 40
- D-Control Connections 41
- USB Connections 42
- Footswitch Connections 42
- Audio Connections 43
- Example XMON Wiring Diagram 46
- Software Configuration 47
- Setting D-Control Preferences 48
- D-Control Guide42 50
- Display Preferences 51
- Meter Preferences 51
- System Calibration 52
- Part III: Reference 53
- Channel Strips 55
- Instrument Tracks 56
- VCA Master Tracks 56
- Bypass/Mute/Pre Switch 57
- Channel Strip Mode Controls 58
- Bypass/Spill Switch 59
- Sends Switch 59
- D-Control Guide52 60
- Fader Section 61
- Channel Strip Master Section 62
- Make Inactive Controls 63
- Plug-in Automation Controls 64
- Assign Controls 65
- Removing Plug-in Assignments 66
- Switch Information Controls 67
- Automation Enable Controls 67
- Automation Write Controls 68
- Global Controls 69
- Set To Default Switch 70
- Suspend Groups Switch 70
- Automation Mode Controls 74
- Talkback Switch 74
- Chapter 7: Plug-in Controls 75
- Default Plug-in Preferences 76
- Targeting Plug-ins 77
- Enabling Plug-in Automation 78
- Reduction on Channel Meters 79
- Dynamics Section 80
- Attack and Release Controls 81
- D-Control Guide74 82
- Dynamics displays 83
- Master Link switch 83
- Bypass indicator 83
- Channel Select switches 83
- Page Switch 84
- External Key Switch 84
- Key Listen Switch 84
- Save As Switch 84
- Gain Reduction Meters 86
- EQ Section 87
- Controls 88
- EQ Controls 88
- Q encoders 89
- Frequency encoders 89
- Gain encoders 89
- Band In switches 89
- EQ displays 90
- Link switch 90
- EQ Edit and Display Controls 91
- Input Gain encoder 92
- Output Gain encoder 92
- Clip indicator 92
- Input meter 92
- Output meter 92
- Transport Section 93
- Scrub/Shuttle Controls 94
- Scrub Switch 95
- Trim Switch 95
- Master Record Mode Switches 96
- Transport Mode Switches 96
- Audition Switches 97
- Locate Switches 97
- External Machines Switches 98
- Zoom/Navigate Section 99
- Bank/Nudge Section 100
- Bank Select Matrix 100
- Window Management Section 101
- Session Management Section 102
- Soft Keys Section 103
- Edit Controls 104
- Select/MIDI Controls 105
- Console Preferences 106
- User Switch 106
- Operation Switch 107
- Automation Controls 108
- Actions Switch (Page 2) 109
- Actions Switch (Page 3) 109
- Actions Switch (Page 4) 109
- Modes Switch 110
- Prefs Switch 110
- Audio Files Switch 111
- Show/Hide Switch 111
- Main and Sub Counter Switches 112
- Link Edit and Timeline Switch 112
- Edit Modes 112
- 1 Press the Go To switch 113
- D-Control Guide106 114
- Monitor Section Controls 115
- Input Source Switches 116
- Sum Switch 116
- Control Room Output Controls 117
- Monitor Output Mode Controls 117
- Monitor Displays 118
- Channel Select Switches 119
- Solo Mode Controls 120
- Headphone/Cue System 121
- Talkback/Listen System 122
- Talkback switch 123
- Talkback Microphone 124
- Meter Displays (Fader Module) 125
- D-Control Guide118 126
- Normal Mode 127
- Plug-in Outputs 128
- Selecting a Track 129
- Focusing a Track 129
- Focusing a Plug-In 130
- Automation Safe Mode 130
- D-Control Guide124 132
- Inline Console Mode 133
- Custom Fader Modes 133
- Custom Fader Preferences 134
- Custom Fader Controls 134
- Custom Groups Mode 134
- Mix/Edit Groups Mode 136
- Tracks Mode 137
- Plug-In Mode 138
- Custom Fader Flip Mode 139
- Custom Fader Map Modes 139
- Plug-in Map Mode 140
- Working with Automation 141
- Joining Automation Values 142
- D-Control Guide136 144
- Appendix A: Utility Mode 145
- Exiting Utility Mode 146
- D-Control System Info Page 146
- D-Control Name Page 146
- D-Control Test Pages 147
- Switch and LED Test Page 148
- Display Test Page 148
- Fader Test Page 149
- Defaults 150
- D-Control Preferences 150
- Display Contrast Page 151
- Sleep Mode Settings Page 151
- D-Control Guide144 152
- Cue Inputs 153
- Cue Outputs 153
- Surround Inputs 154
- Stereo Inputs 154
- Main Speaker Outputs 154
- 15-Pin Connector Pinouts 155
- D-Control Guide148 156
- Numerics 157
- D-Control Guide150 158
- Index 151 159
- D-Control Guide152 160
- Index 153 161
- D-Control Guide154 162
Related products and manuals for Recording Equipment DigiDesign D-Control
(19 pages)© 2020, manymanuals.com. All rights reserved. | 3.667 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals